|
| 10千瓦靜音柴油發電機如何啟動 |
|
 |
|
|
|||||||||||||||||||||||||||||||||
 添加到收藏夾
 點擊發郵件咨詢
 舉報此信息
 收藏到用戶中心
|
| 聯系我時，請說明在東北制造網上看到的，謝謝！ |
 微信分享 |
|
|||
| 關鍵字：10千瓦柴油發電機,靜音柴油發電機,10千瓦靜音發電機,柴油發電機如何啟動,靜音發電機如何啟動,10千瓦靜音柴油發電機 dbzz10千瓦靜音柴油發電機如何啟動柴油發電機組啟動前的準備： 1.檢查潤滑油的油位、 冷卻液液位、燃油量； 2.檢查柴油機的供油、潤滑、冷卻等系統各個管路及接頭有無漏油漏水現象； 3.檢查電氣線路有無破皮等漏電隱患，接地線電氣線路是否松動，機組與基礎的連接是否牢固； 4.若環境溫度低于零度時，須在散熱器內添加一定比例的防凍劑； 5.柴油發電機組次啟動或停機較長時間后再次啟動，應先用手壓泵排盡燃油系統內的空氣。 【品牌名稱】：豹羅動力 【銷售經理】：宋經理 【聯系電話】：18019419802（同微信） 【直線座機】：021-51987469 【電子郵箱】：1736462533@qq.com 【公司名稱】：上海豹羅實業有限公司 【在線QQ】：1736462533 【公司地址】：上海嘉定區葉城路818號 啟動： 1.合上控制箱內的保險后，按啟動按鈕，按下按鈕3~5s，若啟動不成功，應等20s左右再次啟動。若多次啟動不成功，應停止啟動操作，排除電瓶電壓或油路等故障因數后，再次啟動； 2.啟動時應觀察幾油壓力，若油壓無顯示或很低時，應立即停車檢查。 運行： 1.機組啟動后，檢查控制箱模塊各項參數；機油壓力、 水溫、電壓、頻率等； 2.通常情況下，機組啟動后轉速直接達到額定轉速；有怠速要求的機組，怠速時間一般為3~5min，怠速時間不易過長，否則可能燒壞發電機相關元器件； 3.檢查機組油路、水路及電器的滲漏情況； 4.檢查機組各連接處的緊固情況，看有無松動和劇烈振動； 5.觀察機組各種保護和監視裝置是否正常； 6.當轉素達到額定轉速，起空載運行的各項參數穩定后，合閘供電； 7.檢查確認控制屏各項參數是否在允許的范圍內，再次檢查機組的振動，有無三漏及其他故障； 8.機組運行時嚴禁超載。 Preparation of a diesel generating set before starting: 1. check the oil level, coolant level and fuel volume of the lubricating oil. 2. check whether there is leakage or leakage of oil and lubricating oil and cooling system in the diesel engine. 3. check whether there is leakage hazard such as broken electrical wiring, whether the electrical wiring of the grounding wire is loose, and whether the connection between the unit and the foundation is solid. 4. if the ambient temperature is below zero, a certain proportion of antifreeze should be added to the radiator. 5. diesel engine generator start or stop after a long time to start again, should first use the hand pump to exhaust the air in the fuel system. brand name: Leopard power sales manager: manager of song contact: 18019419802 (with WeChat) linear machine: 021-51987469 E mailbox: 1736462533@qq.com Company name: Shanghai leopard Industry Co., Ltd. online QQ: 1736462533 company address No. 818 Yecheng Road, Jiading District, Shanghai. Start: 1. close the control box's insurance, press the start button, press the button 3~5s, if the start is not successful, wait for 20s to start again. If multiple start-up fails, the operation should be stopped and the fault factors such as battery voltage or oil circuit should be removed. 2. several oil pressure should be observed when starting. If the oil pressure is not shown or very low, stop checking immediately. Function： 1. after the unit starts, check the parameters of the control module, oil pressure, water temperature, voltage, frequency, etc. 2. normally, the speed of the unit is directly rated as the speed of the set. The idle speed is generally 3~5min and the idle time is not easy to be too long, otherwise the generator related components may be burned. 3. check the leakage of oil, water and electrical equipment. 4. check the fastening position of each connection point to see if there is loose or violent vibration. 5. observe whether the various protection and monitoring devices are normal. 6. when the converter reaches the rated speed, the various parameters of the no-load operation will be stabilized and the power supply will be closed. 7. check to see if the parameters of the control panel are in the allowed range, check the vibration of the unit again, whether there are three leakage and other faults. Overloading of the 8. unit is strictly prohibited. |
| 最新展會 |
| 網站首頁 - 關于我們 - 使用協議 - 免責條款 - 版權隱私 - 網站地圖 - 友情鏈接 - 廣告服務 - 會員服務 - 免費注冊 - 聯系方式 | ||||||||
| 問題請通過在線提問反饋 | 在線客戶QQ：105452034 | 收費會員及廣告咨詢電話13332201705 技術支持：遼寧衡駿節能科技有限公司 | ||||||||
| Copyright 2007- dbzz.net All Rights Reserved 東北制造網(東北地區唯一制造業網上平臺) 版權所有 遼ICP備2021008091號 遼公網安備21021702000105 | ||||||||
| 為獲得最佳瀏覽效果，建議使用IE7以上，或Firefox7以上瀏覽器 | ||||||||
|
![點擊這里給[ 上海豹羅實業有限公司的張婷 ]發消息](/skin/v1/imgs/qqonline.gif "點擊這里給[ 上海豹羅實業有限公司的張婷 ]發消息")
